Browse all practice questions for the Vermont Natural Gas Certification Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Vermont Natural Gas Certification Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Gas piping can be used as the grounding conductor if the building ground isn't close by. Is this statement true or false?
  • What is the minimum amount of free area required for indoor air openings?
  • Natural gas is mainly comprised of which common hydrocarbon?
  • What percentage of free air space do metal air grills have?
  • An equipment shutoff valve must be located within how many feet of an appliance?
  • What is the heating value of propane gas?
  • What is a prime cause of lifting flames in gas burners?
  • What does a negative air pressure indicate in a natural draft system?
  • The flammable limits of natural gas are defined as which of the following percentage ranges?
  • Which factor is indicated to negatively affect draft in a venting system?
  • What kind of gas is lighter than air?
  • What is one method NOT typically used for producing natural gas?
  • How long must a pressure test last in a residential home?
  • What can be a consequence of inadequate vent capacity in a common venting system?
  • What gauge wire is generally used in a 20A circuit?
  • Can copper be used indoors for natural gas piping in VGS territory?
  • What is the lower flammable limit percentage of natural gas?
  • What happens to the flame when the velocity of the gas-air mixture through the burner ports is reduced below the flame velocity?
  • In electrical terms, what does the letter E denote in the formula P = EI?
  • Which fittings are allowed in concealed locations?
  • What is the specific gravity of natural gas?
  • In Ohm's Law, what does the letter R stand for?
  • According to Watt's Law, what is the relationship between power, voltage, and current?
  • In addition to coated steel pipe, which material does VGS use for its gas mains?
  • What can excessive primary air lead to in a combustion chamber?
  • To prevent damage to underground facilities, who should be contacted before excavating in a public right-of-way?
  • Which of the following fuels produces carbon monoxide (CO) when burned?
  • Which of the following is not a sign of carbon monoxide presence?
  • In what case can living space air be used for combustion?
  • What must be done to remaining gas piping when gas appliances are disconnected and removed?
  • Can a clothes dryer be common vented with a water heater provided the vent capacity is adequate?
  • Is purging required if placing 100ft of 3" pipe into operation?
  • What is a critical step when working with gas piping in residential homes?
  • An appliance with a positive vent pressure that avoids condensation operates under which category?
  • Which property of a gas determines how it behaves when mixed with air?
  • What is the recommended concentration of carbon monoxide (CO) in flue gasses for most heating and water heating appliances?
  • What is the minimum distance a gas water heater or boiler must be from a 275-gal oil tank?
  • What is the term for air supplied to a flame at the point of combustion?
  • Are natural gas appliances typically common vented with wood burning appliances?
  • In building codes, why is venting contractors advised against common venting?
  • Which gauge wire is used in a 30A circuit?
  • What component is essential for a clothes dryer when discussing venting systems?
  • What is the term for the number of times per second that the electrical output of an AC generator goes through one complete cycle?
  • What is the minimum distance double wall (B vent) needs to be from combustibles?
  • What type of gases contribute to a stronger draft in a venting system?
  • What is a potential risk associated with improperly vented dryers?
  • What is the approximate dew point temperature at which water vapor from natural gas combustion condenses?
  • Is it true that gas piping must be electrically bonded to the building ground?
  • In an electrical outlet receptacle, which slot is supposed to be the neutral side?
  • Can natural gas appliances be common vented with oil appliances?
  • Which of the following statements is accurate regarding venting appliances?
  • The standard method for calculating the required air volume for combustion is how many cubic feet per BTU per hour?
  • In case of an uncontrolled escape of gas, what should be the FIRST priority?
  • In Ohm's Law, what does the letter E represent?
  • What is the percentage of nitrogen in the air?
  • Which openings control the flow of secondary air into a combustion chamber?
  • What is the minimum height a B vent must terminate above a roof with a 12/12 pitch?
  • What is the advantage of using double wall pipe?
  • Can a natural draft water heater be installed in a bedroom?
  • Which of the following is NOT a method by which natural gas is created?
  • What unit is used to measure electrical current?
  • According to ANSI standards, flue gases should contain less than how many ppm of carbon monoxide?
  • Which of the following statements about gas leaks is correct?
  • An electromagnetic relay is both a _____ and ______.
  • What type of flames will be observed when primary air is insufficient?
  • Which type of fuel is NOT typically a source of carbon monoxide?
  • In a space of 8' x 20' x 20', what is the required air volume for a 100,000 btu/hr furnace and an 80,000 btu/hr water heater?
  • What must be achieved for complete combustion of natural gas?
  • What are three visual indicators that carbon monoxide may be present in a home?
  • What is NOT a function of a draft hood?
  • What should be done if a gas line breaks?
  • In terms of venting, how should a chimney be treated when replacing or installing a gas furnace?
  • What are three requirements for gas equipment installed in a residential garage?
  • When an electrical switch is closed, will electricity flow through it?
  • Which of the following is a highly efficient appliance option encouraged by the Vermont Energy Code?
  • What is the normal gas pressure inside a customer's home?
  • What percentage of air is made up of oxygen?
  • What is the spacing distance for supports on 3/4" or 1" pipe?
  • What is the correct response regarding the drafting capabilities in systems with hot exhaust gases?
  • Which of the following is NOT a requirement for mechanical draft systems operating under positive vent pressure?
  • In Watt's Law, what does P represent?
  • What are the primary byproducts of the complete combustion of natural gas?
  • What is the minimum height required for the exit terminal of a mechanical draft system above a public walkway?
  • Properly operating natural draft systems create what type of air pressure?
  • Which safety measure can help prevent issues when venting a clothes dryer with a water heater?
  • What can help eliminate extinction pop by reducing the air supplied to the burner?
  • What is the main cause of gas explosions?
  • What can insufficient secondary air supply to a burner in a combustion chamber cause?
  • How is the total air used by an appliance for burning fuel referred to?
  • What type of gas is typically associated with a dryer venting system?
  • Which appliance typically does NOT require a rigid venting system?
  • Does a steam boiler always need a low water cutoff?
  • When installing a multistory vent system, where must all combustion air come from?
  • Is natural gas available in all major cities in Vermont?
  • What is the approximate PSI at which VT Gas operates its transmission line?
  • What is the main advantage of B-vent over single wall pipe?
  • Is natural gas poisonous?
  • What does BTU stand for?
  • For a mechanical draft system, what is one of the critical components that ensures safety?
  • What is the relationship of propane gas to air regarding its weight?
  • What is the minimum height a chimney must be above the highest point of the roof within a horizontal distance of 10 ft?
  • A transformer is both a ______ and a _______.
  • What role does a load play in an electrical circuit?
  • When is a low water cutoff required on a hot water boiler?
  • How many inches must the exit terminal of a mechanical draft system be above the anticipated slow line?
  • What is a primary cause of lifting flames?
  • Which of the following is NOT a common component of natural gas?
  • What defines a direct vent system?
  • What is the primary purpose of secondary air in combustion?
  • What is the heating value of natural gas?
  • What does the Vermont Energy Code aim to reduce?
  • What type of pipe should be used for running underground to a pool heater?
  • What percentage of vent connector capacity is reduced for every additional 90-degree turn beyond the first two elbows?
  • A sediment trap is required on all gas equipment. Is this true or false?
  • How far should single wall galvanized pipe (C vent) be kept from combustibles?
  • How far must a water heater be installed from the front of an electrical breaker box?
  • What is one of the focuses of the Vermont Energy Code regarding resource use?
  • How much higher must a chimney extend above the point of exit through the roof?
  • What is double walled pipe commonly known as?
  • Must existing equipment be brought up to code once a new code has been adopted?
  • After adjusting the gas pressure or changing an orifice, what should you check to ensure correct operation?
  • What is the term for electrons traveling in one direction from negative to positive?
  • What restriction do corrugated chimney liners impose on the capacity of Type B gas vents?
  • When is a chimney considered to be an exterior chimney?
  • Which of the following best describes carbon monoxide?
  • What is the benefit of maintaining correct pitch for venting systems?
  • When assessing burner operation, what should you do after changing an orifice size?
  • What is the minimum height a chimney or vent should be above the draft hood outlet?
  • How can flashback on small port burners usually be eliminated?
  • A device which uses electrical power is also called a _____.
  • The flow area of the vertical vent or chimney should not exceed how many times the area of the smallest flue collar?
  • What does the dew point temperature signify in terms of natural gas combustion?
  • What are the three functions performed by draft hoods?
  • What type of air is circulated to supply oxygen and cool the appliance?
  • Which condition can lead to the formation of yellow-tipped flames in a combustion process?
  • What type of vent pipe is required when passing through attics, floors, or inside walls?
  • Which of the following is NOT a requirement for common venting of multistory systems?
  • Which of the following can result in the spillage of flue products from an appliance draft hood?
  • At approximately what PSI is Compressed Natural Gas transported?
  • Which factor is critical for maintaining safe levels of combustion air?
  • What type of current is generated when a loop of wire is rotated in a gap between the poles of a magnet?
  • How much energy does it take to raise 1 lb of water 1 degree, in BTU?
  • Which organization sets the standards that dictate the regulations for gas piping installations?
  • What should be done if a chimney's vent connector exceeds the specified limit?
  • What is the minimum test pressure for gas piping in residential homes?
  • Which of the following is a measure of resistance?
  • When is it acceptable to use a common vent for a clothes dryer and other appliances?
  • What is the chemical formula for methane?
  • What is a primary concern when choosing fittings for use in concealed locations?
  • What is the importance of sealing all joints in a mechanical draft system?
  • What type of pipe does a B vent represent?
  • Does the neutral wire carry current when the circuit is complete?
  • An appliance that operates with negative vent pressure and a warm temperature is categorized as which type?
  • What percentage of free air space do wood air louvers have?
  • Is a tall chimney preferable to a short chimney?
  • Is natural gas odorless?
  • Which type of appliance must a clothes dryer NOT be vented with under typical best practices?
  • Excess flow of what type of air can lead to inefficient combustion?
  • What is the minimum horizontal distance required for mechanical draft systems?
  • What is the Vermont OSHA exposure limit for carbon monoxide over an 8-hour period?
  • What is the heat input rate (BTU) per hour for a natural gas flow of 80 cu ft/hr?
  • What is the specific gravity of propane?
  • What fitting is not allowed in a concealed location?
  • What is the term for the flow of electric charge in a circuit?
  • In Ohm's Law, what does the letter I represent?
  • Which type of venting material has been discontinued for Category III appliances?
  • Which type of air is directly involved in the combustion process at the burner?
  • What is the force of electrical "pressure" called?
  • The earliest gas burners that were simply open ends of pipe are referred to as what type of flame burners?
  • Which of the following serves as a switching mechanism in an electrical circuit?
  • Which elements can lead to inefficient venting in a gas appliance?
  • When piping through an exterior concrete wall, how must the pipe be treated within the wall?
  • Why is it important to adhere to the Vermont Energy Code?
  • What is the minimum level at which a CO detector will alarm in parts per million (PPM)?
  • What is the minimum ignition temperature of natural gas in degrees Fahrenheit?
  • Which statement is true regarding the installation of heating appliances under the Vermont Energy Code?
  • What is the term for air naturally available to an appliance?
  • What category is assigned to an appliance that has positive vent pressure and experiences condensation?
  • What is the unit of measure for electrical power?
  • Why is it important to ensure adequate vent capacity when venting appliances?
  • What should be considered when estimating vented combustion air needs?
  • What is the optimum burning mixture for natural gas in terms of percentage?
  • What gauge wire is typically used in a 15A circuit?
  • A coupling in an electrical setup mainly serves to do what?
  • In an electrical circuit, the term "source" refers to what?
  • What element of appliance venting is critical for overall safety and efficiency?
  • What is essential for the category of an appliance operating under warm and negative pressure conditions?
  • What is the minimum height above grade for side-wall vent terminations?
  • What are the three basic elements in any electrical circuit?
  • A listed gas connector may pass through a wall provided it's not more than what length?
  • Is plastic vent piping acceptable for new dryer installations?
  • What is the correct response to the statement: "The chimney must be left unlined when venting into an unlined chimney?"
  • What primarily defines whether a dryer can be common vented with other appliances?
  • What is the maximum diameter of threaded fittings permitted above according to NFPA 54?
  • The equation for Watt's Law is expressed as?
  • Which gas has a heating value close to 2500 btu/cubic foot?
  • Why might venting a dryer and water heater together be discouraged?
  • What occurs when a gas burner experiences overpressurization?
  • What is the capacity reduction percentage for vent connectors exceeding 1 1/2 feet per inch of vent connector diameter?
  • What happens to flames when gas pressures are unsteady?
  • NFPA 54 does not permit threaded fittings above _____ inches diameter.
  • How does natural gas compare to air in terms of weight?
  • Do central heating appliances need to be on a dedicated circuit?
  • Using a 1/2 cu. ft per revolution dial on a meter, if it takes 40 seconds for one revolution, what is the gas flow rate in BTU/hr?
  • VT Gas operates its distribution lines at what approximate PSI range?
  • Which measurement indicates the energy content of natural gas?
  • For each cubic foot of natural gas, how many cubic feet of air are required for complete combustion?
  • For residential gas equipment, what does the term "listed equipment" refer to?
  • What is indicated by a yellow-tipped flame during combustion?
  • What type of air is mixed with gas before it reaches the burner port?
  • In addition to natural gas, which other fuel is known to create CO?
  • If an uncontrolled gas leak ignites, should you extinguish the burning gas flame?
  • At what upward pitch should vent connectors be installed?
  • What is a key factor in determining if an appliance should be installed with certain venting conditions?
  • The specific gravity of a gas is a ratio of its density to the density of what?
  • What is the process of removing combustion gases through a vent called?
  • Which of the following statements about air volume for combustion is true?
  • If the velocity of the gas exceeding the flame velocity, what will occur with the flame?
  • What is the upper flammable limit percentage of natural gas?
  • What is required to work on natural gas appliances?
  • How should combustion air openings be sized for appliances?
  • What venting material is required for Category III appliances?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy